Shrink Film Roll Length Calculation: The 3-Inch Core Trap
Formulas linking roll diameter, length and weight, worked metric and imperial examples, a 30–60 μm diameter table, and why core size and trapped air shift the result.
Shrink film roll length calculation turns a roll’s outside diameter, its core’s outside diameter and the film thickness into metres of film, because the ring of film visible on the roll’s end face has an area equal to length times thickness.
Key takeaways
- A “3-inch” core is named for its 76.2 mm bore, but film winds from the outside wall. Using the bore adds a fixed phantom length, about 53 m (173 ft) with the example 92 mm OD core (76 mm bore, 8 mm wall) and 40 μm film, which is under 2% on a 400 mm roll but about 19% on a 150 mm partial roll.
- Trapped air makes real rolls slightly larger than theory, and the ±1.0 μm thickness tolerance (ASTM D374) of JFPolyFilm’s clear PETG film puts a band of up to about ±2.5% on a 40 μm length estimate.
The shrink film roll length calculation formula and where it comes from
One relationship works in both directions: L = π × (D² − d²) / (4 × t) turns a measured diameter into length, and D = √(d² + 4 × L × t / π) predicts the diameter a known length will wind to. Solved for L, it is the roll length calculation formula; solved for D, it sizes a roll before the film is ordered.
L = π × (D² − d²) / (4 × t)
D = √(d² + 4 × L × t / π)
- D: roll diameter (roll OD), measured across the outside of the wound roll, in mm.
- d: the core’s outside diameter (core OD), where winding starts, in mm; the section on core diameter explains why the nominal core size does not belong here.
- t: thickness of one wrap, in μm. On plain film rolls, slit rolls included, this is a single film thickness; on a roll of seamed sleeve tubing each wrap holds two layers, so t is roughly double and the estimate rougher.
- L: roll length, in m.
How a thickness between 30 and 60 μm is chosen is covered in how to choose shrink film thickness.
Core diameter: the formula needs the outside, the name gives the inside
Film starts winding on the core’s outer wall, so d is the core’s outside diameter, while “3-inch” and “6-inch” name the inside diameter, 76.2 mm and 152.4 mm, because the bore has to fit the air shafts on unwind and rewind stands.
| Measured roll diameter | Length with core OD (92 mm) | Length with core ID (76 mm) | Overstatement from using ID |
|---|---|---|---|
| 400 mm (15.7 in) | 2,975 m | 3,028 m | about 1.8% |
| 120 mm (4.7 in) | 117 m | 169 m | about 45% |
Worked examples in metric and imperial units
How to calculate roll diameter from length and thickness is one direction: a known length goes into the D equation to predict diameter.
Example 1: diameter from length.
- Inputs: L = 2,000 m (the length of JFPolyFilm’s 2,000 m sample roll), t = 40 μm, d = 92 mm.
- Substitution: D = √(92² + 4 × 2,000 × 40 / π).
- Result: 8,464 + 101,859 ≈ 110,323, whose square root gives D ≈ 332 mm (13.1 in).
Imperial inputs need one constant: with diameters in inches and thickness in mils, L (ft) = 65.45 × (D² − d²) / t, where 65.45 = π × 1,000 / 48.
Frequently Asked Questions
How many feet of film are on a roll of shrink film?
How long is 15 kg of shrink film?
Why does my calculated roll length not match the label?
Related Articles
How Is PETG Shrink Film Made? Where Roll Quality Is Decided
How PETG shrink film is made, and which production stage sets each line buyers check on arrival: gauge tolerance, TD/MD shrink, haze, tensile strength, roll labels.
Anti-Counterfeit Shrink Sleeves: Layered Brand Protection
How a full-body shrink sleeve carries layered authentication — overt, covert, forensic, and serialized features — and where the film maker's job ends and the converter's begins.
Need Expert Advice on Shrink Film?
Our technical team can help you choose the right film for your application.
Contact Us